FGQXC7WISCBU04F.ino

//>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
// ARDUINO BATTERY CAPACITY TESTER
//Version-1.00
//by deba168,INDIA
//Dated : 04/09/2016
//>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

#include "U8glib.h"
#define MOSFET_Pin 2
#define Bat_Pin A0
#define Res_Pin A1
#define Buzzer_Pin 9
U8GLIB_SH1106_128X64 u8g(U8G_I2C_OPT_NONE);  // I2C / TWI  
float Capacity = 0.0; // Capacity in mAh
float Res_Value = 9.1;  // Resistor Value in Ohm
float Vcc = 4.98; // Voltage of Arduino 5V pin ( Mesured by Multimeter )
float Current = 0.0; // Current in Amp
float mA=0;         // Current in mA
float Bat_Volt = 0.0;  // Battery Voltage 
float Res_Volt = 0.0;  // Voltage at lower end of the Resistor 
float Bat_High = 1.5; // Battery High Voltage
float Bat_Low = 0.9; // Discharge Cut Off Voltage
unsigned long previousMillis = 0; // Previous time in ms
unsigned long millisPassed = 0;  // Current time in ms
float sample1 =0;
float sample2= 0;
int x = 0;
int row = 0;

//************************ OLED Display Draw Function *******************************************************
void draw(void) {
   u8g.setFont(u8g_font_fub14r); // select font
   if ( Bat_Volt < 1){
    u8g.setPrintPos(10,40);        // set position
    u8g.println("No Battery!"); 
   }
   else if ( Bat_Volt > Bat_High){
    u8g.setPrintPos(25,40);        // set position
    u8g.println("High-V!"); 
   }
   else if(Bat_Volt < Bat_Low){
    u8g.setPrintPos(25,40);        // set position
    u8g.println("Low-V!"); 
   }
   else if(Bat_Volt >= Bat_Low && Bat_Volt < Bat_High  ){
      
   u8g.drawStr(0, 20, "Volt: ");   // put string of display at position X, Y
   u8g.drawStr(0, 40, "Curr: ");
   u8g.drawStr(0, 60, "mAh: ");
   u8g.setPrintPos(58,20);        // set position
   u8g.print( Bat_Volt,2);  // display Battery Voltage in Volt
   u8g.println("V"); 
   u8g.setPrintPos(58,40);        // set position
   u8g.print( mA,0);  // display current in mA
   u8g.println("mA"); 
   u8g.setPrintPos(58, 60);        // set position
   u8g.print( Capacity ,1);     // display capacity in mAh
  
}
}
//******************************Buzzer Beep Function *********************************************************

  void beep(unsigned char delay_time){
  analogWrite(9, 20);      // PWM signal to generate beep tone
  delay(delay_time);          // wait for a delayms ms
  analogWrite(Buzzer_Pin, 0);  // 0 turns it off
  delay(delay_time);          // wait for a delayms ms  

}  

//*******************************Setup Function ***************************************************************
  
  void setup() {
   Serial.begin(9600);
   pinMode(MOSFET_Pin, OUTPUT);
   pinMode(Buzzer_Pin, OUTPUT);
   digitalWrite(MOSFET_Pin, LOW);  // MOSFET is off during the start
   Serial.println("CLEARDATA");
   Serial.println("LABEL,Time,Bat_Volt,capacity");
   
   //Serial.println("Arduino Battery Capacity Tester v1.0");
   //Serial.println("BattVolt Current mAh");
  }
  //********************************Main Loop Function***********************************************************
  void loop() {
 // Vcc = readVcc()/1000.0; // Conevrrt mV to Volt

  
  // Voltage devider Out = Bat_Volt * R2/(R1+R2 ) // R1 =10K and R2 =10K 
  
  //************ Measuring Battery Voltage ***********
  
  for(int i=0;i< 100;i++)
  {
   sample1=sample1+analogRead(Bat_Pin); //read the voltage from the divider circuit
   delay (2);
  }
  sample1=sample1/100; 
  Bat_Volt = 2* sample1 *Vcc/ 1024.0; 

  // *********  Measuring Resistor Voltage ***********

   for(int i=0;i< 100;i++)
  {
   sample2=sample2+analogRead(Res_Pin); //read the voltage from the divider circuit
   delay (2);
  }
  sample2=sample2/100;
  Res_Volt = 2* sample2 * Vcc/ 1024.0;

  //********************* Checking the different conditions *************
  
  if ( Bat_Volt > Bat_High){
    digitalWrite(MOSFET_Pin, LOW); // Turned Off the MOSFET // No discharge 
    beep(200);
    Serial.println( "Warning High-V! ");
    delay(1000);
   }
   
   else if(Bat_Volt < Bat_Low){
      digitalWrite(MOSFET_Pin, LOW);
      beep(200);
      Serial.println( "Warning Low-V! ");
      delay(1000);
  }
  else if(Bat_Volt > Bat_Low && Bat_Volt < Bat_High  ) { // Check if the battery voltage is within the safe limit
      digitalWrite(MOSFET_Pin, HIGH);
      millisPassed = millis() - previousMillis;
      Current = (Bat_Volt - Res_Volt) / Res_Value;
      mA = Current * 1000.0 ;
      Capacity = Capacity + mA * (millisPassed / 3600000.0); // 1 Hour = 3600000ms
      previousMillis = millis();
      Serial.print("DATA,TIME,"); Serial.print(Bat_Volt); Serial.print(","); Serial.println(Capacity);
      row++;
      x++;
      delay(4000); 
 
     }
  
   //**************************************************

  u8g.firstPage();  
  do {
    draw();
  } while( u8g.nextPage() );
  
 //*************************************************
 }